This section lists the BE8xxxxx system reference codes.
If the SRC listed in a serviceable event
is missing from the following table, ask your next level of support
for assistance.
Note: Next level, inform development of any SRCs not
defined in the table.
| System Reference Code | Description |
|---|---|
| BE80CB00 | Recovery error, soft device bus error recovered by the IOA. |
| BE80CB01 | Recovery error, device bus fabric error. |
| BE80CB04 | Recovery error, the IOA recovered the logical block LRC error on the host to IOA transfer. |
| BE80CB05 | Recovery error, the IOA recovered the count key data transfer LRC error on the host to IOA transfer. |
| BE80CB06 | Recovery error, the IOA recovered the logical block sequence number error on the host to IOA transfer. |
| BE80CB07 | Recovery error, the IOA recovered the IOADL tag/sequence number error. |
| BE80CB08 | Recovery error, the IOA recovered the logical block CRC error on the IOA to host transfer. |
| BE80CB09 | Recovery error, the IOA recovered the logical block sequence number error on the IOA to host transfer. |
| BE80CB0A | Recovery error, the IOA recovered from a logical block reference tag error. |
| BE80CB0B | Recovery error, the IOA recovered from a logical block guard error. |
| BE80CB0E | Recovery error, IOA sector reassignment successful. |
| BE80CB11 | Recovery error, the IOA recovered the soft PCI bus error. |
| BE80CB12 | Recovery error, the IOA recovered the device hardware error. |
| BE80CB13 | Recovery error, the device recovered the device hardware error. |
| BE80CB14 | Recovery error, the IOA recovered the soft IOA error. |
| BE80CB15 | Recovery error, the IOA recovered the undefined device response. |
| BE80CB17 | Recovery error, failure prediction threshold exceeded. |
| BE80CB1A | IOA not ready, IOA requested reset. |
| BE80CB1C | Media error, data unreadable, recommend reassignment. |
| BE80CB1F | Hardware error, IOA cannot communicate with device. |
| BE80CB20 | Hardware error, device bus error or device error. |
| BE80CB21 | Hardware error, the device or IOA command has timed out. |
| BE80CB22 | Hardware error, device bus fabric error. |
| BE80CB29 | Hardware error, logical block CRC error on IOA to host transfer. |
| BE80CB2B | Hardware error, logical block reference tag error detected by the IOA. |
| BE80CB2C | Hardware error, logical block guard error detected by the IOA. |
| BE80CB2D | Hardware error, IOA reserved area data check. |
| BE80CB2E | Hardware error, the IOA reserved area has an invalid data pattern. |
| BE80CB2F | Hardware error, the IOA reserved area has T10 DIF error. |
| BE80CB30 | Hardware error, reassignment space exceeded. |
| BE80CB31 | Hardware error, data transfer is out of minimum length. |
| BE80CB32 | Hardware error, data transfer is out of maximum length. |
| BE80CB34 | Hardware error, device error. |
| BE80CB35 | Hardware error, IOA Error. |
| BE80CB36 | Hardware error, undefined device response. |
| BE80CB37 | Hardware error, IOA microcode error. |
| BE80CB38 | Hardware error, the IOA must be reset to recover from an error. |
| BE80CB3A | Hardware error, previously missing or failed device detected but has been significantly altered. |
| BE80CB3B | Hardware error, encountered a data check on a read or write performed to a sector just after that sector was reassigned. |
| BE80CB3C | Hardware error, encountered a T10 DIF error on read to a sector just after that sector was written. |
| BE80CB3D | Hardware error, SAS command or task management function failed. |
| BE80CB3E | Hardware error, different (incompatible) device detected at resource address of previously failed device. The new device cannot be utilized. |
| BE80CB3F | Hardware error, invalid multi-adapter configuration. |
| BE80CB40 | Hardware configuration error, incorrect connection between cascaded enclosures. |
| BE80CB41 | Hardware configuration error, connections exceed IOA design limits. |
| BE80CB42 | Hardware configuration error, incorrect multipath connection. |
| BE80CB43 | Hardware error, unsupported enclosure function. |
| BE80CB45 | Hardware error, command to logical unit failed. |
| BE80CB48 | Hardware error, device error, security threshold exceeded. |
| BE80CB49 | Hardware error, IOA error, the encryption password is not correct. |
| BE80CB4A | Unit Attention, rebuild of replaced/repaired device automatically restarted. |
| BE80CB4D | Unit Attention, device bus was reset, expander may be at fault. |
| BE80CB50 | Unit Attention, performance degradation, device bus running at slower than expected speed. |
| BE80CB55 | Unit Attention, asymmetric advanced function DASD configuration. |
| BE80CB56 | Unit Attention, configuration error, incomplete multipath connection between IOA and enclosure. |
| BE80CB57 | Unit Attention, configuration error, incomplete multipath connection between enclosures and device. |
| BE80CB58 | Unit Attention, configuration error, incomplete multipath connection between IOA and remote IOA. |
| BE80CB5A | Unit Attention, enclosure does not support a required multipath function (OEM unit). |
| BE80CB5F | Unit Attention, data loss on logical unit. |
| BE80CB62 | Unit attention, corrupt array parity detected, parity was not resynchronized. |
| BE80CB63 | Unit Attention, array exposed, rebuilding will start soon if there is an available spare. |
| BE80CB66 | Unit attention, array exposed but still protected. |
| BE80CB69 | Unit Attention, Multipath redundancy level is incorrect. |
| BE80CB70 | Data Protect, two or more devices are missing in this array, and only one device is present. |
| BE80CB71 | Data Protect, two or more devices are missing in this array, and two or more devices are present. |
| BE80CB72 | Data Protect, exposed array is short a required device. |
| BE80CB73 | Data Protect, one or more disk array members are not at required physical locations. |
| BE80CB74 | Data Protect, physical location of the disk array members conflict with another disk array. |
| BE80CB75 | Data Protect, previously degraded disk in the disk array not found at required physical location. |
| BE80CB76 | Data Protect, array is missing a device and parity is out of synchronization. |
| BE80CB77 | Data Protect, maximum number of arrays already exist. |
| BE80CB7A | Data Protect, IOA is out of free device identifiers. |
| BE80CB7C | Data Protect, creation of an exposed mode device for an array would cause IOA to exceed the maximum number of devices. |
| BE80CB7D | Data Protect, missing an array out of a volume set, the volume set is not functional. |
| BE80CB80 | Data Protect, maximum number of volume sets already exist. |
| BE80CB82 | SIS adapter unit check data error. |
| BE80CB83 | SIS adapter reset timeout. |
| BE80CBBD | Unit Attention reported due to a storage enclosure RAID controller operating at a high temperature for a prolonged duration. |
| System Reference Code | Description |
|---|---|
| BE820100 | I2C bus 0 hung. |
| BE820101 | I2C bus 1 hung. |
| BE820102 | I2C bus 2 hung. |
| BE820103 | I2C bus 3 hung. |
| BE820104 | I2C bus 4 hung. |
| BE820105 | I2C bus 5 hung. |
| BE820106 | I2C bus 6 hung. |
| BE820107 | I2C bus 7 hung. |
| BE82010F | Fan controller 1 I2C bus received NACK. |
| BE820110 | Fan controller 2 I2C bus received NACK. |
| BE820114 |  Local expander monitoring component (420) has reported an
error. |
| BE820115 | Opposite Expander I2C bus received NACK. |
| BE820116 | Alternate expander monitoring component (420) has reported an
error. |
| BE82011B | Fan 0 is not present or has low RPM. |
| BE82011C | Fan 1 is not present or has low RPM. |
| BE82011D | Fan 2 is not present or has low RPM. |
| BE82011E | Fan 3 is not present or has low RPM. |
| BE820122 | RAID processor on RAID controller C1 temperature sensor read failure. |
| BE820126 | PPC on RAID controller C1 temperature sensor read failure. |
| BE82012A | Expander on RAID controller C1 temperature sensor read failure. |
| BE82012E | Ambient 1 on RAID controller C1 temperature sensor read failure. |
| BE820132 | Ambient 2 on RAID controller C1 temperature sensor read failure. |
| BE820136 | Power supply 1 on RAID controller C1 temperature sensor read failure. |
| BE82013A | Power supply 2 on RAID controller C1 temperature sensor read failure. |
| BE82013E | RAID processor on RAID controller C2 temperature sensor read failure. |
| BE820142 | PPC on RAID controller C2 temperature sensor read failure. |
| BE820146 | Expander on RAID controller C2 temperature sensor read failure. |
| BE82014A | Ambient 1 on RAID controller C2 temperature sensor read failure. |
| BE82014E | Ambient 2 on RAID controller C2 temperature sensor read failure. |
| BE820152 | Power supply 1 on RAID controller C2 temperature sensor read failure. |
| BE820156 | Power supply 2 on RAID controller C2 temperature sensor read failure. |
| BE820160 | Loss of power on both power supplies. |
| BE820161 | Power Supply 1 VPD data error, checksum or corruption. |
| BE820162 | Power Supply 1 no response on I2C interface. |
| BE820163 | Power supply unit (PSU) 1 missing. |
| BE820165 | Power Supply 1 fan fault. |
| BE820166 | Power Supply 1 thermal fault. |
| BE820167 | Power supply unit (PSU) 1, DC over voltage. |
| BE820168 | Power supply unit (PSU) 1, DC under voltage. |
| BE820169 | Power supply unit (PSU) 1, DC over current. |
| BE820170 | Power supply unit (PSU) 2 missing. |
| BE82016A | VCO unit 1, DC under voltage. |
| BE82016B | Power Supply 1 current share warning. |
| BE82016C | Power supply unit (PSU) 1, DC fail. |
| BE82016E | Power Supply 2 VPD data error, checksum or corruption. |
| BE82016F | Power Supply 2 no response on I2C interface. |
| BE820172 | Power Supply 2 fan fault. |
| BE820173 | Power Supply 2 thermal fault. |
| BE820174 | Power supply unit (PSU) 2, DC over voltage. |
| BE820175 | Power supply unit (PSU) 2, DC under voltage. |
| BE820176 | Power supply unit (PSU) 2, DC over current. |
| BE820177 | VCO unit 2, DC under voltage. |
| BE820178 | Power Supply 2 current share warning. |
| BE820179 | Power supply unit (PSU) 2, DC fail. |
| BE820180 | Only RAID controller C1 received PCIe power down request. |
| BE820181 | Unexpected firmware trap. |
| BE820183 | Watchdog timer trip. |
| BE820186 | Power supply unit (PSU) 1, AC fail. |
| BE820187 | Power supply unit (PSU) 2, AC fail. |
| BE820188 | Only RAID controller C2 received PCIe power down request. |
| BE820189 | Storage enclosure statesave complete. |
| BE82018A | Storage enclosure statesave threshold exceeded. |
| BE820200 | ESM VPD checksum failed. |
| BE820201 | Midplane VPD checksum failed. |
| BE820202 | Feature code check failed. |
| BE820203 | VPD migration failed. |
| BE820204 | I2C check failed. |
| BE820205 | Power supply failed. |
| BE820206 | Hot plug controller check failed. |
| BE820207 | Regulator test failed. |
| BE820208 | Fan test failed. |
| BE820209 | Expander clock failed. |
| BE82020A | Internal RAM check failed. |
| BE82020B | ESM VPD check failed. |
| BE82020C | Midplane VPD check failed. |
| BE82020D | I2C check failed. |
| BE82020E | PCI Repeaters check failed. |
| BE82020F | SAS Repeaters check failed. |
| BE820210 | PSoc SGPIO failed. |
| BE820272 | Over temperature, warning threshold exceeded. |
| BE820296 | Over temperature, critical threshold exceeded. |
| BE820300 | PHY Link not ready. |
| BE820301 | PHY Adapt Timer expired. |
| BE820302 | PHY Link not stable. |
| System Reference Code | Description |
|---|---|
| BE83CB81 | Storage enclosure RAID controller unit check error detected. |
| BE83CB82 | Device adapter unit check data error. |
| BE83CB83 | Device adapter reset timeout. |
| BE83CB84 | Device adapter not available because of a firmware error. |
| BE83CB85 | Device adapter command timeout. |
| BE83CB86 | Device adapter ISR unexpected reset error in last path. |
| BE83CB87 | Device adapter ISR unexpected reset error. |
| BE83CB88 | Device adapter ISR generic error. |
| BE83CB89 | Device adapter reset timeout. |
| BE83CB8A | Device adapter HCAM mechanism failure. |
| BE83CB8B | Device adapter configuration HCAM overflow. |
| BE83CB8C | Device adapter general ASM error. |
| BE83CB8D | Device adapter ASM firmware download error. |
| BE83CB8E | Device adapter ISR unrecoverable hardware error. |
| BE83CB93 | Device adapter user requested reset reached threshold, adapter fenced. |
| BE83CB94 | Device adapter I/O command has timed out. |
| BE83CB98 | SIS adapter has detected an IOCTL watchdog timeout condition. |
| BE83CB9B | SIS adapter requested reset to collect dump. |
| BE83CBB1 | Storage enclosure RAID controller firmware image on the LPAR is missing or corrupted. |
| BE83CBB2 | Storage enclosure RAID controller not available as a hot standby. |
| BE83CBB5 | Storage enclosure RAID controller generic problem detected by device adapter (DA) microcode. |
| BE83CBB6 | Storage enclosure RAID controller heartbeat timeout detected by device adapter (DA) microcode. |
| BE83CBB8 | Storage enclosure RAID controller slow drive timeout detected by device adapter (DA) microcode. |
| BE83CBB9 | Storage enclosure RAID controller detected DMA failure. |
| System Reference Code | Description |
|---|---|
| BE840054 | Drive was marked for deferred sparing. |
| BE840055 | Drive install certify failed due to microcode logic error |
| BE840056 | Unexpected number of drives within the same adapter reported as failed. |