DS8000 Service Documentation Version 7.5

Ethernet (8-port) switch part numbers, Model 941

Information about Ethernet switch parts is listed below. See Figure 1 for switch locations.

Note: The following part numbers are the most recent for this version of the Parts Catalog. Your storage facility or serviceable event FRU list might contain an older or newer part number. The parts ordering system recognizes all valid part numbers and will automatically substitute an available part number as needed.
Figure 1. 8-port Ethernet switch locations
8-port Ethernet switch locations
Table 1. Ethernet switch parts (Model 941)
Index Part name Part number
SW1/SW2 8-port Ethernet switch assembly (includes switch, power adapter, and sheet metal pre-assembled) 21R9558
45W5222

Cables for Ethernet switch SW1 (left)

To find part numbers for the cables that are connected to Ethernet switch SW1 (the left Ethernet switch), see Figure 2, Figure 3, and Table 2.

Figure 2. 8-port Ethernet cable locations (1 through 9)
8-port Ethernet cable locations (1 through 9)
Figure 3. 8-port Ethernet cable locations (10 through 13)
8-port Ethernet cable locations (10 through 13)
Table 2. Cables for Ethernet switch SW1 (left) (Model 941)
Index Part name Part number
1 Cable, Ethernet switch SW1 -to- HMC (1750 mm black) 45W2258
2 (Call your next level of support)  
3 Cable, Ethernet switch SW1 -to- CEC enclosure XC11 FSP (870 mm black) 45W2358
4 Cable, Ethernet switch SW1 -to- CEC enclosure XC22 FSP (1070 mm black) 45W2359
5 Cable, Ethernet switch SW1 -to- CEC enclosure XC11 (1070 mm black) 45W2360
6 Cable, Ethernet switch SW1 -to- CEC enclosure XC22 (1280 mm black) 45W2361
7 Not used
8 Not used
9 This power cable is part of the power adapter in the Ethernet switch assembly. N/A
10 See Table 1.
11 M5 screw 23R1520
12 Multi-connector power cord3 22R5759
13 8-port Ethernet switch assembly mounting shelf 21R9562
Notes:
  1. XC1 is the upper CEC enclosure.
  2. XC2 is the lower CEC enclosure.
  3. This cord is hardwired to a junction connector that receives power from both PPSs. The junction connector also supplies power to the management console, the display/keyboard tray, and Ethernet switch SW2.

Cables for Ethernet switch SW2 (right)

To find part numbers for the cables that are connected to Ethernet switch SW2 (the right Ethernet switch), see Figure 2, Figure 3, and Table 3.

Table 3. Cables for Ethernet switch SW2 (right) (Model 941)
Index Part name Part number
1 Cable, Ethernet switch SW2 -to- HMC (1580 mm gray) 45W2262
2 (Call your next level of support)  
3 Cable, Ethernet switch SW2 -to- CEC enclosure XC11 FSP (660 mm gray) 45W2362
4 Cable, Ethernet switch SW2 -to- CEC enclosure XC22 FSP (870 mm gray) 45W2363
5 Cable, Ethernet switch SW2 -to- CEC enclosure XC11 (870 mm gray) 45W2364
6 Cable, Ethernet switch SW2 -to- CEC enclosure XC22 (1070 mm gray) 45W2365
7 Not used
8 Not used
9 This power cable is part of the power adapter in the Ethernet switch assembly. N/A
10 See Table 1.
11 M5 screw 23R1520
12 Multi-connector power cord3 22R0842
13 8-port Ethernet switch assembly mounting shelf 21R9562
Notes:
  1. XC1 is the upper CEC enclosure.
  2. XC2 is the lower CEC enclosure.
  3. This cord is hardwired to a junction connector that receives power from both PPSs. The junction connector also supplies power to the management console, the display/keyboard tray, and Ethernet switch SW1.